Fixes: - MegaRAID iMR FW with "enableReducedFeatureSet=1" issue - After the newest image is installed, servers often will not boot. - FW sending wrong configuration data during boot msg pending state - Not able to change the properties of MSM. - Upgrading from Software RAID to 9260-8i causes Alarm to sound - Error in MR_DCMD_CTRL_EVENT_COUNT/SL_DIR_READ - MSM log warning: Controller booted in headless mode with errors - Data Corruption with R5 cachedIO mode - Sequential Read performance is less on CacheCade associated LD's. - Montask occurs when running host i/o and parallel OOB command - Generic point release MR4.9 :VPD output of lspci vvxxx showing [RV] Reserved: checksum bad, 86 byte(s) reserved - When pinned cache present VD property not changing from WB to WT. - 9260-8i(SAS2108) hitting OOB SRAT timeout for a long time causing OOB commands to fail - Check-in Pl version 5.0.42.0-- Improve STP connection timing behavior with idle connections - Checking-in new PL version :05.00.41 - To check-in new PL version 5.00.40.00 - Discard preserved cache takes excessive time or hangs - Controller always gives an event MR_EVT_CTRL_BOOT_HEADLESS_MODE_HAD_ERRORS if controller is set in HSM mode. - Montask occurs when running host i/o and parallel OOB command - PDs go online without VD created & App doesn't allow any VD creation on passing a wrong parameter in Spanned VD. - To Disable the logging of event MR_EVT_PD_EMERGENCY_SPARE_COMMISSIONED_REMINDER - EEprom CRC error is detected when WebBIOS is running - STP Passthrough Support through OOB - FW is not declaring the battery bad if learn cycles fail continuously - Validate the requested blocks for SCSI VERIFY commands on RAID volumes - See 9261-8i emergency spare being commissioned - Data Miscompare found while running I/O overnight with degraded virtual drives - FW halts when you have pinned cahce and remove VD form the configuration. - FW halts when you have pinned cahce and remove VD form the configuration. - Card Running iMR Machine Checks when Requesting Host Memory - Minimum Capacity needed for relearn is incorrect in 2208 MR FW - Incorrect variable type in MR Read/Modify/Write path - RM_SataBBMTotalCount always return 0 - FW Automatically detect backplane SGPIO type to set the driveactivityLED parameter - Setting the ASO key with storcli 1.02.08 (MegaCli 8.07.06) fails with an error code 3 on Windows or Linux if the MB BIOS PCI - Discard preserved cache takes excessive time or hangs - During rebuild on PRL11 CacheCade VD and rebuild on RAID6 Source VD IO integrity error is seen. - IO integrity error seen after Source VD associated with CacheCade VD is forcibly unblocked - LDBBM on RAID6 not eligible - PCIe core has received a PCIe request that it does not support - Firmware returns asc value as 0 when failing IOs with medium errors - Firmware hits Montask when drive is pulled after changing the volume property from read ahead to no read ahead. - Faulty protocol used for changing the Disk Write Cache Policy - BU SOH bad message be posted after exhauting retry attempts. Stop monitoring battery once SOH bad is declared - RHEL6.4 Kernel crash after reboot - Medium error correction event is not logged during CC - Firmware Version 2.130.383-2912 is hitting MonTask at line 1209 in file ../../raid/1078dma.c - Source VD gets blocked on OCR after one PD removal from R0 WB CCVD and reuse of that PD in creating another CCVD. - Data Corruption seen when IOs are in progress and cachecade PD is marked as missing and reused to create another SSC VD. - Sequential Read performance is less on CacheCade associated LD's. - When a Cachecade PD marked as missing is reused to make Cachecade VD IO integrity error is observed. - Saved Release Note DataSLIB returning bad data as good data after host reboots - (Vital Product Data) needs to identify PCB hardware level - Validate the requested blocks for SCSI VERIFY commands on RAID volumes - If a BOOT Passphrase is enabled with SafeStor "MegaCli adpbios dsply a0" will display "BIOS will Stop on error" even if any other mode is set. - Update the events - Firmware is not updating recovery timer as intended - "chip paused" causes high service time on all drives - 9260-8i(SAS2108) hitting OOB SRAT timeout for a long time causing OOB commands to fail - Raid configuration loss after reboot- PDs in POWERSAVE - Code Review: Call DDF_discardInvalidPds only if DS3 is enabled - Upgrading from Software RAID to 9260-8i causes Alarm to sound - System black screen during S1 Sleep test - UEFI driver issue with platforms when user having 2TB or 4TB VD - Platfrom has UEFI hang when SATA is connected - Disable Debug print in UEFI Driver - Block IO tests from SCT IHV test suite failed - ATA PT: Follow UEFI Spec on interpreting In and Out Transfer Length that upper layer sends - Obtain the Physical Slot number from the PCI Bridge to which the Controller is connected. - Memory access issue for when loading Ctrl R - Memory allocation: Allocate only two 64k Versions: - NVDATA 3.09.03-0054 - BootBlock 2.02.00.00-0001 - ROMENV 1.08 - WebBIOS 4.0-60-e_49-Rel - PCLI 03.02.20 - UEFI_Driver 0x05290000 - Hii 1.38.00 - BIOS 4.37.00 This download is valid for the product(s) listed below. - Intel Integrated RAID Module RMS2AF040 - Intel Integrated RAID Module RMS2AF080 - Intel RAID Controller RS2WC040 - Intel RAID Controller RS2WC080
Скачать