Программы для ВконтактеNetgear KWGR614 Firmware 1.0.0_09.25
- Размер: 1.8 MB
- ОС: Win All
- Имя файла: kwgr614_1_0_0_09_25na.bix
This version is for North America Only!
Note: Do not upgrade the firmware using a wireless connection. Please perform firmware upgrade with “wired” or Ethernet connection only.
New Features
1. Added the “Dynamic L2TP” support (in additional to the Static L2TP) for some ISP broadband accesses.
2. Added the feature to avoid “LAN/WAN IP configuration conflict”: this version can detect and avoid the installation problem automatically when the WAN side uses the conflicting IP address configuration as the LAN side.
3. The 1st release of the NA (Northern American) firmware compliant with the FCC requirement: the wireless region is fixed to US, and only channel 1~channel 11 selection allowed. The wireless radio is ON by default. The default Time Zone is US.
4. Intel ViiV certifiable: implemented the hidden page (“router-info.htm”) for the access of the Intel ViiV management software.
5. The 1st release of the WW (worldwide) firmware for EU, AU, etc (except US)
6. SIP ALG supported for VoIP applications
7. Added the system recovery capability: In case the flash image is damaged (because of improper or interrupted upgrade process, or bad firmware image programmed by the open source developers, etc), this version allows re-loading the firmware via TFTP. The procedure is:
1. Power off the unit
2. Press and hold the RESET button at the rear panel
3. Power on to reboot the unit
4. Monitor the Test LED, and keep holding the RESET button until the Test LED changes from blinking to steady ON (which means the boot loader has entered the TFTP recovery mode)
5. Connect the PC to the LAN port of the unit
6. Transmit the firmware image file to the unit:
For Windows PC, enter the DOS command: tftp -i 192.168.1.1 PUT KWGR614_XXX.bix
For a Linux PC, use the command: tftp -m binary 192.168.1.1 -c put KWGR614_XXX.bix
where the “192.168.1.1” is the unit’s LAN IP address and “KWGR614_XXX.bix” is the firmware image file to transmit.
7. Monitor the Test LED. When it starts blinking, the recovery procedure is complete
8. Power cycle to reboot KWGR614
Repeat the above steps if the procedure is interrupted or failed.
Known Issues
1. Video and Audio of ICQ5 connection cannot be established.
NETGEAR has been a worldwide provider of technologically advanced, branded networking products since 1996. Our mission is to be the preferred customer-driven provider of innovative networking solutions for small businesses and homes.
It is highly recommended to always use the most recent driver version available.
Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.
Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.
Примечание: Ссылка "скачать" может вести как непосредственно на файл, так и на сайт производителя, на котором Вы можете найти нужный файл.
Это связано с тем, что некоторые производители не позволяют размещать прямые ссылки на файлы.
Note: Do not upgrade the firmware using a wireless connection. Please perform firmware upgrade with “wired” or Ethernet connection only.
New Features
1. Added the “Dynamic L2TP” support (in additional to the Static L2TP) for some ISP broadband accesses.
2. Added the feature to avoid “LAN/WAN IP configuration conflict”: this version can detect and avoid the installation problem automatically when the WAN side uses the conflicting IP address configuration as the LAN side.
3. The 1st release of the NA (Northern American) firmware compliant with the FCC requirement: the wireless region is fixed to US, and only channel 1~channel 11 selection allowed. The wireless radio is ON by default. The default Time Zone is US.
4. Intel ViiV certifiable: implemented the hidden page (“router-info.htm”) for the access of the Intel ViiV management software.
5. The 1st release of the WW (worldwide) firmware for EU, AU, etc (except US)
6. SIP ALG supported for VoIP applications
7. Added the system recovery capability: In case the flash image is damaged (because of improper or interrupted upgrade process, or bad firmware image programmed by the open source developers, etc), this version allows re-loading the firmware via TFTP. The procedure is:
1. Power off the unit
2. Press and hold the RESET button at the rear panel
3. Power on to reboot the unit
4. Monitor the Test LED, and keep holding the RESET button until the Test LED changes from blinking to steady ON (which means the boot loader has entered the TFTP recovery mode)
5. Connect the PC to the LAN port of the unit
6. Transmit the firmware image file to the unit:
For Windows PC, enter the DOS command: tftp -i 192.168.1.1 PUT KWGR614_XXX.bix
For a Linux PC, use the command: tftp -m binary 192.168.1.1 -c put KWGR614_XXX.bix
where the “192.168.1.1” is the unit’s LAN IP address and “KWGR614_XXX.bix” is the firmware image file to transmit.
7. Monitor the Test LED. When it starts blinking, the recovery procedure is complete
8. Power cycle to reboot KWGR614
Repeat the above steps if the procedure is interrupted or failed.
Known Issues
1. Video and Audio of ICQ5 connection cannot be established.
NETGEAR has been a worldwide provider of technologically advanced, branded networking products since 1996. Our mission is to be the preferred customer-driven provider of innovative networking solutions for small businesses and homes.
It is highly recommended to always use the most recent driver version available.
Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.
Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.
Примечание: Ссылка "скачать" может вести как непосредственно на файл, так и на сайт производителя, на котором Вы можете найти нужный файл.
Это связано с тем, что некоторые производители не позволяют размещать прямые ссылки на файлы.
Идёт загрузка...