Скачать драйвер для Netgear FVS338 Firmware 1.6.35

New Features Overview

Version 1.6.35

XAUTH (Extended Authentication) and RADIUS Support for VPN
XAUTH is configured in IKE Policy menu, RADIUS in new Radius Client menu.

NetBIOS Broadcast Support over VPN
Configured in VPN Policy menu.

Version 1.6.29

IKE Mode Config
Mode Config allows a remote VPN client to obtain a virtual IP address and other IP configuration information (DNS, WINS, etc) from the router.

Modifications and Bug Fixes

Version 1.6.35

1. Fixed: IKE in fail-over was not updating the MyAddr field when local IP Address was configured with FQDN.
2. Fixed disconnecting Dialup after rollover.
3. Fixed load balancing and failover issues.
4. Added support for US Robotics modem.
5. Added failover detection using PING instead of DNS.
6. Fixed NNTP (newsgroups) bug.
7. Fixed Cisco VPN interoperability issue.
8. Fixed DynDNS issue.
9. Fixed DHCP issues.
10. Fixed inbound rules disappearing.
11. Fixed PPPoE LCP issue.
12. Fixed MTU reset to 1500 after reboot.
13. Fixed Microsoft Root Certificate loading.
14. Can add more than 129 inbound rules.

Version 1.6.29

1. Update mode config help menu.
2. Fixed conflicts between mode config and regular client configurations.
3. Fixed DynDNS issues.
4. Fixed failover problem from Dialup to BroadBand ISP.

Version 1.6.26

1. PPPoE stability problems are fixed.
2. Can now add custom services up to 125 services.
3. Increased the total number of possible rules to 600.
4. SMTP login name can now accept up to 50 characters.
5. Problem in disabling inbound rules is fixed.
6. VPN interoperability improvements.

Version 1.6.23

1. FQDN support with Main mode added to VPN Wizard.
2. Disable VPN policy will drop tunnel now.
3. Manual switch over to broadband will access Internet now.
4. DynDNS status fixed.
5. VPN remote can now be configured to Any.
6. PPPoE MTU value is now set to 1492 by default.
7. Fixed dropped packets in VPN tunnel.

Version 1.6.17

1. Added support for modem hardware flow control signals.
2. Added image upgrade header validation so router will not upload the wrong image.
3. Modified AES key length selection menu.
4. Guest (read-only) default login password changed to password.

Version 1.6.15

1. VPN throughput increased.
2. Number of simultaneous sessions increased.
3. Guest (read-only) password can now be changed separately (default is guest).
4. Fixed crash from SNMP daemon.
5. Fixed GUI hang when accessing Statistics window.
6. Fixed unrequested blocking of websites.
7. Fixed operation of factory default button.
8. Default gateway is now shown in routing table.
9. Fixed issue when changing from static to PPPoE WAN.
10. Fixed: VPN traffic stops when heavy traffic.
11. Removed One-to-one NAT table and Exposed Host, since these can be done with Inbound Rules.

Known Issues

1. May need to toggle Daylight Savings Time setting after upgrade.
2. BigPond login may not work correctly.
3. If you were having problems with reserved IP addresses in Groups and Hosts, you may need to perform a factory default reset after upgrading to the newer version.
4. Can't edit VPN policy to change LAN subnet.
5. An attempt to access a blocked site is not logged.





It is highly recommended to always use the most recent driver version available.
Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.

Примечание: Ссылка "скачать" может вести как непосредственно на файл, так и на сайт производителя, на котором Вы можете найти нужный файл.
Это связано с тем, что некоторые производители не позволяют размещать прямые ссылки на файлы.