Скачать драйвер для Intel P4000CP Server System EFI Firmware 02.02.0002

Versions:
- BIOS: 02.02.0002
- ME: 02.01.07.328
- BMC: 01.20.5446
- FRUSDR: 1.10

Changes in BIOS 02.02.0002:
- Fixed: The system can't power up after restoring the BIOS default value via removing the CMOS battery

Changes in ME 2.01.07.328:
- Fixed: Platform is not able to power on properly after being shut down by NM Policy
- Fixed: Global platform power consumption reported by NM Statistics in S5 is incorrect
- Fixed: OOB (out-of-band) stress test by issuing the wrong username may cause connection to be unavailable
- Fixed: Shutdown action can be interrupted by cold reset when volatile NM policy is in use

Changes in BMC 01.20.5446:
- Fixed: The Embedded Web Console was showing the incorrect version of ME Firmware when the ME was in firmware update mode.
- Fixed: Nothing displayed on the Embedded Web Console while logging in with an IPv6 address (stateless ICMPv6 discovery).
- Fixed: BMC Embedded Web Console session not maintained with a power cycle
- Fixed: System does not maintain BMC web console session during power state change or system reset.
- Fixed: The Intel Xeon Phi Coprocessor adapters numbering is not consistent with riser slot numbering on server board.
- Fixed: Embedded Web Console SEL text log not decoding BIOS update versions correctly.
- Fixed: No video display in BMC KVM when SUT wakes up from S1 or S3 in Windows* 2012.
- Fixed: S2600IP - Intel Xeon Phi Coprocessor adapter MIC Status 7 shows as Unknown in some configurations.
- Fixed: S2600GZ - Intel Xeon Phi Coprocessor adapter MIC Status Sensor shows "Unknown" when only 1 MIC card exists in system.
- Fixed: Cannot set link-local gateway for BMC Network Management Interface using IPv6.
- Fixed: [X] Web Console not defaulting to English when another non-English browser is detected.
- Fixed: Add Cross Frame Options to prevent cross-frame scripting of Embedded Web Console
- Fixed: Browser autocomplete enabled before authentication.
- Fixed: SMI Timeout errors not logging IIO Global error registers in Debug Log
- Fixed: BMC LAN connection not working after IP address change.
- Fixed: Multi-node boards with node ID 1111 are not regarded as a single node.
- Fixed: BMC email alerts refused by some servers.
- Fixed: IP address of baseboard management NIC can't be configured successfully when dynamic and static IP changed.
- Fixed: The baseboard management NIC can't get a dynamic IP address when the VLAN set as enable.
- Fixed: Change to 1600W PSU firmware for an acoustic issue.
- Fixed: POST Error code 0xA6A0 was causing the SEL page to fail to render.
- Also fixes decode of POST Error code 0x0012 and invalid POST Errors causing the SEL page to fail to render.
- Fixed: The ME firmware has 2 minor versions in the update related SEL.
- Updated the OEM command format to support this.
- Added: Support Intel Xeon Phi Coprocessor adapters in Intel Server Boards and Systems.
 - Added: Added a button on Web to enable/disable IPMI over LAN.

This download is valid for the products listed below:
- Intel Server Board S2600CP Family
- Intel Server System P4000CP Family


It is highly recommended to always use the most recent driver version available.

Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.

Примечание: Ссылка "скачать" может вести как непосредственно на файл, так и на сайт производителя, на котором Вы можете найти нужный файл.
Это связано с тем, что некоторые производители не позволяют размещать прямые ссылки на файлы.