Скачать драйвер для D-Link DWL-8200AP REVB Firmware 2.10

Fixes:
Problem Resolved:
[SNMP] dot11SecAccountingServerPort node cannot get value.
[WEB] When VLAN state is enabled, change the MSSID’s security will disable MSSID’s state.
[Firmware] STA couldn’t connect to multi-ssid of 11a band when eth, wlan0, wlan1 use the same mac address. So change the mac address rule back to original
[Firmware] It should send an IAPP-ADD-Notify packet when STA roaming to AP2 from AP1, not only an IAPP-Move-Notify packet.
[Firmware] Change the MAC address rule, eth, wlan0, wlan1 use the same mac address.
[SNMP] Fix SNMP show "00:00:00:00:00:00" mac address in 11A band.
[MIB] Support WDS client info.
[FW] Intel WiFi Link 4965AGN can’t connect to AP if authentication is WPA/WPA2 PSK, and vlan state is enabled.
[FW] Fix the Microsoft SilverlightIE compatibility issue.
[FW] AP couldn’t connect to fast radius.
[FW] Modify the channel list in 11a band for U3 domain.
[FW] Enhance the MSSID over WDS function, allow user change the security settings of MSSID when the ap mpde is WDS with AP.
[FW]Support maximum community string length to 32 characters.
[WEB] The Vlan tag mode should be set to Manual when Authentication is not WPA in multi-ssid page.
[WEB] If enable Vlan state when the AP mode is WDS, it should pop up a warning message.
[WEB] AP will crash if save Rouge AP detection info before the Radar scan complete.
[WEB] User can’t configure a valid IP address(such as X.255.X.X or X.X.255.X) as a DHCP Start Address in DHCP Server page.
[FW] A/G band IGMP snp cannot play simultaneous
[WEB] The dynamic vlan mode can not set successful on the multi-ssid page of 802.11a.
[WEB] If set the authentication to WPA-EAP, the multi-ssid page display imperfectly.
[WEB] User can’t set Wireless MAC ACL.
[WEB] If ap mode is not normal ap, then Grouping should be gray and can't set.
[WEB] Enable VLAN State when the multi state is disabled, the radio button of band should point to “both”.
[WEB] There should be a warning message, when changing primary ssid’s authentication will affect MSSID’s authentication.
[CLI] When WDS or WDS with AP mode is set, disable CLI command about ratecontrol and supportrate.
[FW] Only permit user manage the ap through Lan1.
[FW] Mssid over WDS function has some conflict with Mssid Eth to WM filter policy, it won’t take effect if the Mssid Eth to WM filter policy is enable.
[FW] Broadcast packets may miss four bytes if Vlan is enable, this will cause two station can not communicate between 802.11a&802.11g on the same vlan.
[FW] Trap can’t send.
[FW]When MSSID is enabled and authentication type is WPA-PSK in secondary SSID, the STAs which associated to secondary SSID failed to ping each other.

Enhancements:
[FW] Support APMII v2.0.
[FW] Modify the channel list in 11a band as the latest output power table sepc.
[FW] Support NAP function based on dynamic vlan.
[FW] Support Primary SSID with VLAN tag function
[FW] Support Administration VLAN(Manage VLAN) , administrate AP with WLAN and management IP range function
[FW] Trap server settings(categorize the types of traps)
[FW] Support MSSID over WDS
[FW] WMM over WDS
[FW] Priority by SSID
[FW] IGMP Snooping (v1/v2)
[FW] 802.1X Dynamic VLAN
[FW] Data Rate Control follows Dlink new spec.
[FW] Support IAPP (fast roaming)
[FW] Enable/Disable ping
Secondary RADIUS server setting
[FW] AP status on UI (also on MIB)
CPU and Memory utilization
Statistics for Ethernet TX and RX bytes and packets
[WEB]SSID change wireless network name (SSID)
[MIB]Support 802.11MIB
[MIB]Support MIB-II (RFC-1213)
[MIB]Support Trap002-1 spec
[CLI] CLI command to input SNMP Location.
[CLI] Hide the commands, get targetPower/gett controlPower/get swPower ,in CLI
[CLI]Open 3 RSTP commands, rstp getstp/rstp getstate/rstp setstate


It is highly recommended to always use the most recent driver version available.

Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.

Примечание: Ссылка "скачать" может вести как непосредственно на файл, так и на сайт производителя, на котором Вы можете найти нужный файл.
Это связано с тем, что некоторые производители не позволяют размещать прямые ссылки на файлы.