Скачать драйвер для CradlePoint IBR650 Router Firmware 5.0.0

New features added in this release:
- Added support for new modems.
- VPN Improvements – Internet / OpenVPN. OpenVPN has been added to provide SSL VPN support.
- L2TP support for a WAN interface is provided under Internet / L2TP Tunnels.
- GRE: Failover/Failback and WAN Binding support has been added.
- VPN Failback. This feature allows two or more VPN tunnels to be created that will failover if one connection goes down and will fail back if the higher priority connection is available. It is configured in the VPN Tunnels wizard / Dead Peer Detection page.
- Filter packets going through the modem that do not match the network. This feature is enabled by default and can be disabled using Internet / Connection Manager / Common Defaults / Modem Settings.
- Internet / CP Connect (Beta feature in 5.0). CP Connect tunnels can be used to create a connection to a private network.
- Internet / WiFi as WAN. (MBR1400v2 only). WPA2 Enterprise Authentication added to Wi-Fi as WAN option.
- Zscaler cloud-based filtering/security added under Network Settings / Content Filter / Cloud Based Filtering/Security.
- SMS access. Now enabled for all products on this platform.

Extended Enterprise License:
- System Settings / Feature Licenses. An Extended Enterprise License will enable a number of features on those routers.
- Routers upgrading from earlier firmware versions will automatically be granted a license to the existing features that will fall under the EEL (STP, VRRP, etc.).

Additional UI/Usability changes:
- First Time Setup Wizard / Configuring Failure Check. Enabling Failure Check here will default Ethernet and WiFi as WAN checks to use a ping, and modems to Passive DNS.
- Added IP WAN Subnet Filter checkbox to Modem Settings.
- Added Enable AUX Antenna checkbox to Modem Settings. When disabled, the embedded modem’s AUX antenna is turned off.

Defects fixed:
- PMTU issue with IPSEC/VPN
- System Stats SINR graph moved backwards
- GPS change. GPS was being reported in degrees and decimal degrees. Now it is reported as degrees, minutes, and seconds.
- USB Serial hardware flow control issue
- AT&T Beam (Netgear AC340U) now works with i2gold SIMs

Modems tested:
- CradlePoint MC200LP2-EU / EE, Vodafone (UK), Tele2 (Sweden) / Supported on MBR1400, CBA750B Only
- Netgear AC341U (“NETGEAR 341U USB Modem”) / Sprint (USA)
- Pantech UML295VW (“Verizon 4G LTE USB Modem UML2954G LTE”) / Verizon (USA)

Important:
- Note 1: Before upgrading to new firmware, it is always a good idea to save the configuration file from your current version. This firmware version will remove a configuration for version 3.2 or lower and will not try to keep your settings.
- Note 2: Revision 5.0.0 is a significant change from previous releases. Updating from prior versions to 5.0.0 through the router UI or ECM will keep all current settings. Factory resetting 5.0.0 and then re-applying a saved configuration from an earlier version may not reset all saved passwords correctly. Downgrading from 5.0.0 or later to an earlier version WILL force a factory reset on the router. Saving a 5.0.0 or later configuration and applying it to an earlier version will change any non-default passwords to an unknown string.


It is highly recommended to always use the most recent driver version available.

Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.

Примечание: Ссылка "скачать" может вести как непосредственно на файл, так и на сайт производителя, на котором Вы можете найти нужный файл.
Это связано с тем, что некоторые производители не позволяют размещать прямые ссылки на файлы.